Hazardous Location Applications

WARNING:

• Hazardous Locations

• It is the user's responsibility to ensure that all local, state, and national laws, rules, codes, or regulations relating to

the installation and use of this device in any particular application are satisfied. This device must be installed by

Qualified Persons, in accordance with this document and applicable regulations.

• A Qualified Person is a person who, by possession of a recognized degree or certificate of professional training, or

who, by extensive knowledge, training and experience, has successfully demonstrated the ability to solve problems

relating to the subject matter and work.

WARNING: The hazardous location mounting hardware is designed to help protect the HLS27 light from damage during

impact and must be used in all hazardous location applications. Failure to use the Banner supplied mounting hardware

correctly will void the hazardous location rating of the light.

CAUTION:

• Electrostatic Discharge (ESD) Special Conditions for Safe Use

• Parts of the enclosure are non-conducting and can generate an ignition-capable level of ESD.

• Clean the equipment with only a damp cloth.

General Notes and Conditions for Safe Use:

• See Specifications and Wiring Diagrams for important information concerning entity parameters, permissible locations, electrical

connections and certifications.

• In addition to the warning above concerning user responsibility, the installation must comply with the following:

◦

All installations must comply with all manufacturer's instructions.

▪

This device is provided with a PLTC-ER/ITC-ER cable and must be installed in accordance with the following:

• NEC Article 501.10 (B) for Class I Division 2

• NEC Article 502.10 (B) for Class II Division 2

• NEC Article 503.10 (A) or (B) for Class III Division 1 or 2 respectively

• Canadian Electrical Code (CSA C22.1) for Canadian Installations

• Section 9 of IEC 60079-14 for ATEX/IECEx locations

▪

The PLTCER/ITC-ER cable shall be installed in accordance with the provisions of NEC Article 725 (PLTC-ER) or 727.4 (ITC-

ER) for Class I Division 2, Class II Division 2, and Class III Division 1 and 2 locations

▪

The cable shall be terminated with a fitting certified for the appropriate location classification

▪

The device must be powered by a class 2 power supply

• Do not attempt any repairs to this device; it contains no field-replaceable parts or components. Tampering and/or replacement with non-

factory components may adversely affect the safe use of the system.

• The nonconducting materials of this device may be susceptible to ignition-capable level of electrostatic charging and precautions must be

taken to avoid this. The user/installer shall ensure that the equipment is not installed in a location where it may be subjected to external

conditions (such as high-pressure steam) which are conducive to creating a build-up of electrostatic charges.

• The user/installer must take suitable precautions to prevent the device from being adversely affected by aggressive substances, such as

acidic liquids or gases that may attack metals, or solvents that may affect polymeric (plastic) materials. Suitable precautions include routine

inspection or maintenance procedures require replacement of damaged devices or establishing from the materials data sheet that the

device is resistant to specific chemicals. These precautions must ensure that the type of protection is not compromised.

Wiring Diagram

Wire Color

Single Color Models

Dual Color Models

PWM Models

12–30 V dc

–

+

3

1

4

1 - Brown

12 V dc to 30 V dc

Color 1: 12 V dc to 30 V dc

12 V dc to 30 V dc

3 - Blue

dc common

dc common

dc common

4 - Black

Connect to 12 V dc to 30 V dc for 50%

intensity. For 100% intensity, leave the

black wire floating or connected to

common.

Color 2: 12 V dc to 30 V dc (color 2

overrides color 1)

Pulse width modulation (PWM) input. For

maximum intensity, leave the black wire floating or

connected to common. Connecting to 12 V dc to

30 V dc will cause LEDs to shut off.

Mounting Instructions

Multiple mounting options are available for the HLS27 in hazardous locations. In the two options listed below, the mounting brackets must be

spaced a distance of (L4) apart to ensure the device meets impact protection standards for hazardous locations.

Included Mounting Hardware (LMBHLS27S – 2 Brackets)

When using the standard mounting hardware, the mounting hole centers for each individual bracket

must be spaced 50.0 mm (1.97 inches) from one another. This spacing is critical for the bracket to

provide the required impact protection and prevent rotation of the light within the bracket.

The stainless-steel bracket is designed to be used with M5 or #10 stainless-steel hardware.

HLS27 Hazardous Location LED Strip Light

2

www.bannerengineering.com - Tel: + 1 888 373 6767

P/N 197949 Rev. B