| Zakładka z wyszukiwarką danych komponentów |
|
INA293 Arkusz danych(PDF) 14 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
INA293 Arkusz danych(HTML) 14 Page - Texas Instruments |
|
14 / 27 page ![]() Output Voltage (V) 0 1 2 3 200 400 600 800 1000 1200 1400 INA293A1 INA293A2 INA293A3 INA293A4 INA293A5 Figure 7-1. Bandwidth vs Output Voltage 7.3.1.2 Low Input Bias Current The INA293-Q1 inputs draw a 20-µA (typical) bias current at a common-mode voltage as high as 110 V, which enables precision current sensing on applications that require lower current leakage. 7.3.1.3 Low VSENSE Operation The INA293-Q1 operates with high performance across the entire valid VSENSE range. The zero-drift input architecture of the INA293-Q1 provides the low offset voltage and low offset drift needed to measure low VSENSE levels accurately across the wide operating temperature of –40 °C to +125 °C. Low VSENSE operation is particularly beneficial when using low ohmic shunts for low current measurements, as power losses across the shunt are significantly reduced. 7.3.1.4 Wide Fixed Gain Output The INA293-Q1 gain error is < 0.15% at room temperature, with a maximum drift of 10 ppm/°C over the full temperature range of –40°C to +125°C. The INA293-Q1 is available in multiple gain options of 20 V/V, 50 V/V, 100 V/V, 200 V/V, and 500 V/V, which the system designer should select based on their desired signal-to-noise ratio and other system requirements. The INA293-Q1 closed-loop gain is set by a precision, low drift internal resistor network. The ratio of these resistors are excellently matched, while the absolute values may vary significantly. Adding additional resistance around the INA293-Q1 to change the effective gain is not recommended, however, because of this variation. The typical values of the gain resistors are described in Table 7-1. Table 7-1. Fixed Gain Resistor GAIN R1 RL 20 (V/V) 25 kΩ 500 kΩ 50 (V/V) 10 kΩ 500 kΩ 100 (V/V) 10 kΩ 1000 kΩ 200 (V/V) 5 kΩ 1000 kΩ 500 (V/V) 2 kΩ 1000 kΩ 7.3.1.5 Wide Supply Range The INA293-Q1 operates with a wide supply range from 2.7 V to 20 V. The output stage supports a wide output range while INA293-Q1x1 (gain of 20 V/V) at a supply voltage of 20 V allows a maximum acceptable differential input of 1 V. When paired with the small input offset voltage of the INA293-Q1, systems with very wide dynamic range of current measurement can be supported. INA293-Q1 SBOS870A – MAY 2019 – REVISED SEPTEMBER 2020 www.ti.com 14 Submit Document Feedback Copyright © 2020 Texas Instruments Incorporated Product Folder Links: INA293-Q1 |
|
Link URL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Link do karty katalogowej | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |