MODEL: MSP6

MSP6 SPECIFICATIONS

ES-4853 Rev.19 Page 2/5

http://www.m-system.co.jp/

(Select ‘With Terminal Box.’)

Long-life Potentiometer

blank: Standard potentiometer

/P: Long-life potentiometer (for 20 mm stroke only)

(Not available when /L or /B is selected)

Other Options

blank: none

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q

EX-FACTORY SETTING

/SET: Preset according to the Ordering Information Sheet

(No. ESU-4854)

GENERAL SPECIFICATIONS

Degree of protection: IP66

Action: Direct or Reverse; field selectable with DIP switches

Ex-factory setting: Reverse

In "Reverse" action, the output stem moves upward as the

input signal increases when the actuator is mounted

upright.

Operation at abnormally low input:

- Retract/move upward

- Extend/move downward

- Stop

Ex-factory setting: Extend/move downward

(The operation direction of the output stem when the

actuator is mounted upright)

Field selectable with DIP switches

Abnormal signal level: -16 ±2.5 %

Electrical connection

•Without terminal box

•With terminal box

(Sequential control signal suffix code: B)

Wiring conduit: G 1/2 female (two)

Terminal screws: M3 pillar terminal

•With terminal box

(Sequential control signal suffix code: other than B)

Wiring conduit: G 1/2 female (two)

Terminal screws: M3 chromated steel

(torque 0.5 N·m)

Housing material: Diecast aluminum (ADC.12)

Drive: Stepping motor

Insulation class: E

Position detection: Potentiometer

- Common specification (contact conductive)

Deadband: 0.1 – 4.5 % adjustable

Ex-factory setting: 1.5 %

Restarting timer: 0 – 10 sec.

Ex-factory setting: 1.5 sec.

Isolation: AC power to signal

Zero adjustment: 0 – 25 %

Span adjustment: 50 - 100 %

Protective functions: Overload (lock) protection

Power indicator: Green LED is ON while power is supplied

Input indicator: Green LED is ON while normal signal is input

Status indicator LED: Red LED blinks at intervals of: 2 sec. in

normal operation; and 0.5 sec. when an overload (lock) is

detected

Manual operating handle: Not available

Output stem operation distance and adjustable range

3: 10 - 20 mm

- Ex-factory setting: 0 - 20 mm

- Adjustable range: 0 - 10 mm (min. distance)

4: 20 - 40 mm (Not available for /P)

- Ex-factory setting: 0 - 40 mm

- Adjustable range: 0 - 20mm (min. distance)

Y: 10 - 22 mm (Not available for /P)

- Ex-factory setting: 0 - 20 mm

- Adjustable range: 0 - 22 mm (max. distance)

- Adjustable range: 0 - 10 mm (min. distance)

INPUT SPECIFICATIONS

■ DC Current: Input resistor incorporated (250 Ω)

■ DC Voltage: 1 – 5 V DC or specific range within 0 – 5 V

DC, minimum span 1 V

(For a current input, convert the current to a voltage with

250 Ω)

Input resistance: Approx. 1 MΩ

■ Forced open/close signal: Dry contact inputs to command

to go up and go down

Rating: 5 V DC @ 2.5 mA

(go up and go down when upright mount)

OUTPUT SPECIFICATIONS

■ Operation Time & Torque (at rated power voltage)

MSP6-x3: 5 sec. /10 mm 600 N (135 lbf)

MSP6-x4: 8 sec. /10 mm 1200 N (270 lbf)

MSP6-x6: 15 sec. /10 mm 2500 N (562 lbf)

■ DC Voltage: 1 – 5 V DC (not isolated)

With “direct” action, 5 – 1 V DC position output is provided

proportionally to 4 – 20 mA DC (1 – 5 V DC) input.

Load resistance: ≥ 5 kΩ

■ Full-open / -closed signals: Limit switch contact

Rating: 125 V AC @ 0.75 A (cos ø = 1)

30 V DC @ 0.6 A (resistive load)

Maximum operation frequency: 60 cycles/min.