ADATE205 datasheet(7/16 Pages) AD

7 / 16 page

ADATE205

Rev. 0 | Page 7 of 16

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

VDUT Range

−1.5

+6.5

|VDUT − VCOM| > 1.0 V

VDUT Range

−1.5

+6.5

VDUT − VCOM > 1.0 V,

IOH = 0 mA to 35 mA

VDUT Range

−1.5

+6.5

VCOM − VDUT > 1.0 V,

IOL = 0 mA to 35 mA

Output characteristics

Gain

9.5

10.5

mA/V

Slope of line between 5 mA and

30 mA

Load Offset, IOH, IOLT

−200

+200

μA

IOH and IOL programmed at

20 mV (200 μA)

Load Nonlinearity, IOH, IOLT

−50

+50

μA

Relative to a line from 5 mA to

30 mA; IOL, IOH from 200 μA to

35 mA

Output Current Tempco, IOH, IOLT

±3

μA/C

Measured at IOH, IOL = 30 mA

VCOM Buffer (Through Bridge)

VCOM Buffer Offset

IOL, IOH = 20 mA, VCOM = 0 V

VCOM Buffer Bias Current

−10

+10

μA

VCOM = −1.5 V to +6.5 V

VCOM Buffer Gain

0.99

1.01

V/V

IOL, IOH = 20 mA,

VCOM = −1.5 V to +6.5 V

VCOM Buffer Linearity Error

−10

+10

IOL, IOH = 20 mA,

VCOM = −1.5 V to +6.5 V, relative

to a line at 0 V and 5 V

Dynamic Performance

Propagation Delay—IMAX to INHIBIT

2.3

VTT = 2 V, VCOM = 4 V/0 V,

IOL = 20 mA, IOH = 20 mA

INHIBIT to IMAX

2.3

VTT = 2 V, VCOM = 4 V/0 V,

IOL = 20 mA, IOH = 20 mA

TOTAL FUNCTION

Output Leakage Current

−1.5

+0.28

+1.5

μA

Driver = INH, VDUT swept from

−1.5 V to +6.5 V

Output Leakage Current, Low Leakage Mode

−200

+10

+200

Driver = INH, VDUT swept from

−1.5 V to +6.5 V

Output Capacitance

Power Supplies5

Total Supply Range

15.5

Positive Supply, VCC

9.75

10.0

10.25

Negative Supply, VEE

−5.25

−5.0

−4.75

Positive Supply Current, VCC

160

180

205

Load enabled at 20 mA, driver is

set to VIL = 0 V

Negative Supply Current, VEE

210

240

270

Load enabled at 20 mA, driver is

set to VIL = 0 V

Total Power Dissipation

Load enabled at 20 mA, driver is

set to VIL = 0 V

Positive Supply Current Load Disabled, VCC

115

135

170

Load enabled at 0 mA, driver is

set to VIL = 0 V

Negative Supply Current Load Disabled, VEE

160

190

220

Load enabled at 0 mA, driver is

set to VIL = 0 V

Total Power Dissipation

1.3

2.3

2.8

Load enabled at 0 mA, driver is

set to VIL = 0 V

Temperature Sensor Gain Factor

mV/°C

Five diodes in series

1 1 μs period, pulse width = 50 ns to 500 ps, pulse width measured when amplitude drops 10%.

2 Measured at 50% of input amp to 50% of output amp.

3 tPD measured from the 50% of enable signal to 50% of output.

4 The low leakage mode of the comparator, controlled by VLLM input, reduces the leakage due to the comparator input. The comparator operates in this mode, but its

bandwidth is compromised and is not guaranteed.

5 Under no circumstances should the input voltages exceed the supply voltages.

ADATE205 Arkusz danych(PDF) 7 Page - Analog Devices

ADATE205 Arkusz danych(HTML) 7 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Arkusz danych Pobierz

Link URL