LM3200 datasheet(4/15 Pages) NSC

4 / 15 page

Electrical Characteristics (Notes 2, 7) Limits in standard typeface are for T

A =TJ = 25˚C. Limits in boldface

type apply over the full operating ambient temperature range (−25˚C

≤ T

A =TJ

≤ +85˚C). Unless otherwise noted,

specifications apply to the LM3200 with: PV

IN =VDD = EN = 3.6V, BYP = 0V. (Continued)

Symbol

Parameter

Conditions

Min

Typ

Max

Units

Logic Low Input

Threshold for EN, BYP

0.4

Pin Pull Down Current

for EN, BYP

EN, BYP = 3.6V

µA

Gain

CON to VOUT Gain

V/V

CON

CON Input Leakage

Current

CON = 1.2V

System Characteristics The following spec table entries are guaranteed by design if the component values

in the typical application circuit are used. These parameters are not guaranteed by production testing.

Symbol

Parameter

Conditions

Min

Typ

Max

Units

RESPONSE Time for VOUT to Rise

from 0.8V to 3.4V in

PWM Mode

IN = 4.2V, COUT = 4.7 µF,

LOAD =15

Ω

L = 2.2 uH

µs

CON

CON Input

Capacitance

CON = 1V,

Test frequency = 100 kHz

ON_BYP

Bypass FET Turn On

Time In Bypass Mode

IN = 3.6V, VCON = 0.267V,

OUT = 4.7 µF, RLOAD =15

Ω

BYP = Low to High

µs

BYP

Auto Bypass Detect

Delay Time

(Note 10)

µs

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of

the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the

Electrical Characteristics tables.

Note 2: All voltages are with respect to the potential at the GND pins.

Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150˚C (typ.) and disengages at TJ =

130˚C (typ.).

Note 4: The Human body model is a 100 pF capacitor discharged through a 1.5 k

Ω resistor into each pin. (MIL-STD-883 3015.7) The machine model is a 200 pF

capacitor discharged directly into each pin. National Semiconductor recommends that all integrated circuits be handled with Appropriate precautions. Failure to

observe proper ESD handling techniques can result in damage.

Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be

de-rated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125˚C), the maximum power

dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (θJA), as given by the

following equation: TA-MAX =TJ-MAX-OP –(θJA xPD-MAX).

Note 6: Junction-to-ambient thermal resistance (

θJA) is taken from thermal measurements, performed under the conditions and guidelines set forth in the JEDEC

standard JESD51-7. A 1" x 1", 4 layer, 1.5 oz. Cu board was used for the measurements.

Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm.

Note 8: The LM3200 is designed for mobile phone applications where turn-on after power-up is controlled by the system controller and where requirements for a

small package size overrule increased die size for internal Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin low

until the input voltage exceeds 2.7V.

Note 9: Over-Voltage protection (OVP) threshold is the voltage above the nominal VOUT where the OVP comparator turns off the PFET switch while in PWM mode.

Note 10: VIN is compared to the programmed output voltage (VOUT). When VIN–VOUT falls below VBYPASS− for longer than TBYP the Bypass FET turns on and the

switching FETs turn off. This is called the Bypass mode. Bypass mode is exited when VIN–VOUT exceeds VBYPASS

+ for longer than T

BYP, and PWM mode returns.

The hysterisis for the bypass detection threshold VBYPASS

+ –V

BYPASS− will always be positive and will be approximately 200 mV(typ.).

Note 11: Shutdown current includes leakage current of PFET and Bypass FET.

Note 12: Electrical Characteristic table reflects open loop data (FB=0V and current drawn from SW pin ramped up until cycle by cycle current limit is activated).

Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Closed loop current limit is the peak inductor current

measured in the application circuit by increasing output current until output voltage drops by 10%.

Note 13: Bypass FET current limit is defined as the load current at which the FB voltage is 1V lower than VIN.

LM3200 Arkusz danych(PDF) 4 Page - National Semiconductor (TI)

LM3200 Arkusz danych(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Arkusz danych Pobierz

Link URL