TUSB2046

4-PORT HUB FOR THE UNIVERSAL SERIAL BUS

WITH OPTIONAL SERIAL EEPROM INTERFACE

SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999

4

POST OFFICE BOX 655303

Terminal Functions

TERMINAL

I/O

DESCRIPTION

NAME

NO.

I/O

DESCRIPTION

BUSPWR

8

I

Power source indicator. BUSPWR is an active high input that indicates whether the downstream ports source

their power from the USB cable or a local power supply. For the bus-power mode, this pin should be pulled

to 3.3 V, and for the self-powered mode, this pin should be pulled low. Input must not change dynamically

during operation.

DM0

2

I/O

Root port USB differential data minus. DM0 paired with DP0 constitutes the upstream USB port.

DM1 – DM4

11, 15,

19, 23

I/O

USB differential data minus. DM1 – DM4 paired with DP1 – DP4 support up to four downstream USB ports.

DP0

1

I/O

Root port USB differential data plus. DP0 paired with DM0 constitutes the upstream USB port.

DP1 – DP4

12, 16,

20, 24

I/O

USB differential data plus. DP1 – DP4 paired with DM1 – DM4 support up to four downstream USB ports.

EECLK

5

O

EEPROM serial clock. When EXTMEM is high, the EEPROM interace is disabled. The EECLK pin is disabled

and should be left floating (unconnected). When EXTMEM is low, EECLK acts as a 3-state serial clock output

to the EEPROM with a 100

µA internal pulldown.

EEDATA/

GANGED

6

I/O

EEPROM serial data/power management mode indicator. When EXTMEM is high, EEDATA/GANGED

selects between gang or per-port power over-current detection for the downstream ports. When EXTMEM

is low, EEDATA/GANGED acts as a serial data I/O for the EEPROM and is internally pulled down with a

100

µA pulldown. This standard TTL input must not change dynamically during operation.

EXTMEM

26

I

EEPROM read enable. When EXTMEM is high, the serial EEPROM interface of the device is disabled. When

EXTMEM is low, terminals 5 and 6 are configured as the clock and data pins of the serial EEPROM interface,

respectively.

GND

7, 28

Ground. GND terminals must be tied to ground for proper operation.

OVRCUR1 –

OVRCUR4

10, 14,

18, 22

I

Over-current input. OVRCUR1 – OVRCUR4 are active low. For per-port over current detection, one

over-current input is available for each of the four downstream ports. In the ganged mode, any OVRCUR input

may be used and all OVRCUR pins should be tied together. OVRCUR pins are active low inputs with noise

filtering logic.

PWRON1 –

PWRON4

9, 13,

17, 21

O

Power-on/-off control signals. PWRON1 – PWRON4 are active low, push-pull outputs. Push-pull outputs

eliminate the pullup resistors which open-drain outputs require. However, the external power switches that

connect to these pins must be able to operate with 3.3-V inputs because these outputs cannot drive 5-V

signals.

RESET

4

I

Reset. RESET is an active low TTL input with hysteresis and must be asserted at power up. When RESET

is asserted, all logic is initialized.

SUSPND

32

O

Suspend status. SUSPND is an active high output available for external logic power down operations. During

the suspend mode, SUSPND is high. SUSPND is low for normal operation.

TSTMODE

31

I

Test pin. TSTMODE is used as a test pin during production testing. This pin must be tied to ground for normal

operation.

TSTPLL

27

I/O

Test pin. TSTPLL is used as a test pin during production testing. This pin must be tied to ground for normal

operation

VCC

3, 25

3.3-V supply voltage

XTAL1

30

I

Crystal 1. XTAL1 is a 6-MHz crystal input with 50% duty cycle. An internal PLL generates the 48-MHz and

12-MHz clocks used internally by the ASIC logic.

XTAL2

29

O

Crystal 2. XTAL2 is a 6-MHz crystal output. This terminal should be left open when using an oscillator.