HCPL-2201 datasheet(13/18 Pages) AVAGO

13 / 18 page

Notes:

1. Each channel.

2. Derate total package power dissipation, P

T, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.

3. Duration of output short circuit time should not exceed 10 ms.

4. For single devices, input capacitance is measured between pin 2 and pin 3.

5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.

6. The t

PLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of

the output pulse. The t

PHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the

trailing edge of the output pulse.

7. CM

H is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.

L is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.

8. For HCPL-2202/12, V

O is on pin 6.

9. Use of a 0.1

µF bypass capacitor connected between pins 5 and 8 is recommended.

10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage

detection current limit, I

I-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/

EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.

11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage

detection current limit, I

I-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/

EN/DIN EN 60747-5-2 Insulation Characteristics Table.

12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.

Package Characteristics

Parameter

Sym.

Min.

Typ.

Max.

Units

Test Conditions

Fig.

Note

Input-Output Momentary

ISO

3750

V rms

RH < 50%, t = 1 min.

5, 10

HCNW22XX

5000

A = 25°C

5, 11

Input-Output Resistance

I-O

1012

I-O = 500 Vdc

HCNW22XX

1012

1013

A = 25°C

1011

A = 100°C

Input-Output Capacitance

I-O

0.6

f = 1 MHz,

HCNW22XX

0.5

0.6

A = 25°C, VI-O = 0 Vdc

Input-Input Insulation

I-I

0.005

µA

Relative Humidity = 45%,

Leakage Current

t = 5 s, V

I-I = 500 V

Resistance (Input-Input)

I-I

1011

I-I = 500 V

Capacitance (Input-Input)

I-I

0.25

f = 1 MHz

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage

rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level

safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203

Withstand

Voltage*

HCPL-2201 Arkusz danych(PDF) 13 Page - AVAGO TECHNOLOGIES LIMITED

HCPL-2201 Arkusz danych(HTML) 13 Page - AVAGO TECHNOLOGIES LIMITED

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Arkusz danych Pobierz

Link URL