LT1207CS datasheet(3/16 Pages) LINER

3 / 16 page

LT1207

VCM = 0, ±5V ≤ VS ≤ ±15V, pulse tested, VSHDN A = 0V, VSHDN B = 0V, unless otherwise noted.

ELECTRICAL CHARACTERISTICS

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Noninverting Input Current

VS = ±5V to ±15V

500

nA/V

Power Supply Rejection

Inverting Input Current

VS = ±5V to ±15V

0.7

µA/V

Power Supply Rejection

Large-Signal Voltage Gain

VS = ±15V, VOUT = ±10V, RL = 50Ω

VS = ±5V, VOUT = ±2V, RL = 25Ω

ROL

Transresistance,

∆VOUT/∆IIN–

VS = ±15V, VOUT = ±10V, RL = 50Ω

100

260

Ω

VS = ±5V, VOUT = ±2V, RL = 25Ω

200

Ω

VOUT

Maximum Output Voltage Swing

VS = ±15V, RL = 50Ω, TA = 25°C

±11.5

±12.5

±10.0

VS = ±5V, RL = 25Ω, TA = 25°C

±2.5

±3.0

±2.0

IOUT

Maximum Output Current

RL = 1Ω

250

500

1200

Supply Current per Amplifier

VS = ±15V, VSHDN = 0V, TA = 25°C20

Supply Current per Amplifier,

VS = ±15V, TA = 25°C12

RSHDN = 51k (Note 4)

Positive Supply Current

VS = ±15V, VSHDN A = 15V, VSHDN B = 15V

200

µA

per Amplifier, Shutdown

Output Leakage Current, Shutdown

VS = ±15V, VSHDN = 15V, VOUT = 0V

µA

Slew Rate (Note 5)

AV = 2, TA = 25°C

400

900

µs

Differential Gain (Note 6)

VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω

0.02

Differential Phase (Note 6)

VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω

0.17

DEG

Small-Signal Bandwidth

VS = ±15V, Peaking ≤ 0.5dB

MHz

RF = RG = 620Ω, RL = 100Ω

VS = ±15V, Peaking ≤ 0.5dB

MHz

RF = RG = 649Ω, RL = 50Ω

VS = ±15V, Peaking ≤ 0.5dB

MHz

RF = RG = 698Ω, RL = 30Ω

VS = ±15V, Peaking ≤ 0.5dB

MHz

RF = RG = 825Ω, RL = 10Ω

Note 3: Thermal resistance

θJA varies from 40°C/W to 60°C/W depending

upon the amount of PC board metal attached to the device.

θJA is specified

for a 2500mm2 test board covered with 2oz copper on both sides.

Note 4: RSHDN is connected between the Shutdown pin and ground.

Note 5: Slew rate is measured at

±5V on a ±10V output signal while

operating on

±15V supplies with RF = 1.5k, RG = 1.5k and RL = 400Ω.

Note 6: NTSC composite video with an output level of 2V.

The q denotes specifications which apply for 0

°C ≤ TA ≤ 70°C.

Note 1: Applies to short circuits to ground only. A short circuit between

the output and either supply may permanently damage the part when

operated on supplies greater than

±10V.

Note 2: Commercial grade parts are designed to operate over the

temperature range of – 40

°C to 85°C but are neither tested nor guaranteed

beyond 0

°C to 70°C. Industrial grade parts tested over –40°C to 85°C are

available on special request. Consult factory.

LT1207CS Arkusz danych(PDF) 3 Page - Linear Technology

LT1207CS Arkusz danych(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Arkusz danych Pobierz

Link URL