MCP48FVB22 datasheet(29/84 Pages) MICROCHIP

29 / 84 page

 2015 Microchip Technology Inc.

DS20005466A-page 29

MCP48FVBXX

4.0

GENERAL DESCRIPTION

The MCP48FVBX1 (MCP48FVB01, MCP48FVB11,

and MCP48FVB21) devices are single-channel voltage

output devices. The MCP48FVBX2 (MCP48FVB02,

MCP48FVB12, and MCP48FVB22) devices are

dual-channel voltage output devices.

These devices are offered with 8-bit (MCP48FVB0X),

10-bit (MCP48FVB1X) and 12-bit (MCP48FVB2X)

resolution and include volatile memory, an SPI serial

interface and a write latch (LAT) pin to control the

update of the written DAC value to the DAC output pin.

The devices use a resistor ladder architecture. The

resistor

ladder

DAC

driven

from

software-selectable voltage reference source. The

source can be either the device’s internal VDD, an

external VREF pin voltage (buffered or unbuffered) or

an internal band gap voltage source.

The DAC output is buffered with a low-power,

precision output amplifier (op amp). This output

amplifier provides a rail-to-rail output with low offset

voltage and low noise. The gain (1x or 2x) of the

output buffer is software configurable.

The devices operate from a single supply voltage. This

voltage is specified from 2.7V to 5.5V for full specified

operation, and from 1.8V to 5.5V for digital operation.

The devices operate between 1.8V and 2.7V, but

some device parameters are not specified.

The main functional blocks are:

• Power-on Reset/Brown-out Reset (POR/BOR)

• Device Memory

• Resistor Ladder

• Output Buffer/VOUT Operation

• Internal Band Gap (as a voltage reference)

• SPI Serial Interface Module

4.1

Power-on Reset/Brown-out Reset

(POR/BOR)

The internal Power-on Reset (POR)/Brown-out Reset

(BOR) circuit monitors the power supply voltage (VDD)

during operation. This circuit ensures correct device

start-up at system power-up and power-down events.

The device’s RAM retention voltage (VRAM) is lower

than the POR/BOR voltage trip point (VPOR/VBOR).

The maximum VPOR/VBOR voltage is less than 1.8V.

POR occurs as the voltage is rising (typically from 0V),

while BOR occurs as the voltage is falling (typically

from VDD(MIN) or higher).

The POR and BOR trip points are at the same voltage,

and the condition is determined by whether the

VDD voltage is rising or falling (see Figure 4-1). What

occurs is different depending on whether the reset is a

POR or a BOR.

When

VPOR/VBOR <VDD < 2.7V,

the

electrical

performance

may

not

meet

the

data

sheet

specifications. In this region, the device is capable of

reading and writing to its volatile memory if the proper

serial command is executed.

MCP48FVB22 Arkusz danych(PDF) 29 Page - Microchip Technology

MCP48FVB22 Arkusz danych(HTML) 29 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

Arkusz danych Pobierz

Link URL