FS32K118LAT0MLHT datasheet(39/84 Pages) NXP

39 / 84 page

Table 25. NVM reliability specifications (continued)

Symbol

Description

Min.

Typ.

Max.

Unit

Notes

When using FlexMemory feature : FlexRAM as Emulated EEPROM

tnvmretee

Data retention

—

years

nnvmwree16

nnvmwree256

Write endurance

• EEPROM backup to FlexRAM ratio = 16

• EEPROM backup to FlexRAM ratio = 256

100 K

1.6 M

—

writes

5, 6, 7

1. Data retention period per block begins upon initial user factory programming or after each subsequent erase.

2. Program and Erase for PFlash and DFlash are supported across product temperature specification in Normal Mode (not

supported in HSRUN mode).

3. Cycling endurance is per DFlash or PFlash Sector.

4. Data retention period per block begins upon initial user factory programming or after each subsequent erase. Background

maintenance operations during normal FlexRAM usage extend effective data retention life beyond 5 years.

5. FlexMemory write endurance specified for 16-bit and/or 32-bit writes to FlexRAM and is supported across product

temperature specification in Normal Mode (not supported in HSRUN mode). Greater write endurance may be achieved

with larger ratios of EEPROM backup to FlexRAM.

6. For usage of any EEE driver other than the FlexMemory feature, the endurance spec will fall back to the specified

endurance value of the D-Flash specification (1K).

7. FlexMemory calculator tool is available at NXP web site for help in estimation of the maximum write endurance achievable

at specific EEPROM/FlexRAM ratios. The “In Spec” portions of the online calculator refer to the NVM reliability

specifications section of data sheet. This calculator is only applies to the FlexMemory feature.

6.3.2 QuadSPI AC specifications

The following table describes the QuadSPI electrical characteristics.

• Measurements are with maximum output load of 25 pF, input transition of 1 ns and

pad configured with fastest slew settings (DSE = 1'b1).

• I/O operating voltage ranges from 2.97 V to 3.6 V

• While doing the mode transition (RUN -> HSRUN or HSRUN -> RUN ), the

interface should be OFF.

• Add 50 ohm series termination on board in QuadSPI SCK for Flash A to avoid loop

back reflection when using in Internal DQS (PAD Loopback) mode.

• QuadSPI trace length should be 3 inches.

• For non-Quad mode of operation if external device doesn’t have pull-up feature,

external pull-up needs to be added at board level for non-used pads.

• With external pull-up, performance of the interface may degrade based on load

associated with external pull-up.

Memory and memory interfaces

S32K1xx Data Sheet, Rev. 9, 09/2018

NXP Semiconductors

FS32K118LAT0MLHT Arkusz danych(PDF) 39 Page - NXP Semiconductors

FS32K118LAT0MLHT Arkusz danych(HTML) 39 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

Arkusz danych Pobierz

Link URL