| Zakładka z wyszukiwarką danych komponentów |
|
TMP17 Arkusz danych(PDF) 7 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
TMP17 Arkusz danych(HTML) 7 Page - Analog Devices |
|
7 / 8 page ![]() REV. A TMP17 –7– RHIGH and RLOW determine the limits of temperature controlled by the potentiometer RSET. The circuit shown operates over the temperature range –25 C to +105 C. The reference maintains a constant set point voltage and ensures that approximately 7 V appear across the sensor. If it is necessary to guardband for extraneous noise, hysteresis can be added by tying a resistor from the output to the ungrounded end of RLOW. Multiple remote temperatures can be measured using several TMP17s with a CMOS multiplexer or a series of 5 V logic gates because of the device’s current-mode output and supply-voltage compliance range. The on resistance of a FET switch or output impedance of a gate will not affect the accuracy, as long as 4 V is maintained across the transducer. Muxes and logic driving circuits should be chosen to minimize leakage current related errors. Figure 13 illustrates a locally controlled mux switching the signal current from several remote TMP17s. CMOS or TTL gates can also be used to switch the TMP17 supply voltages, with the multiplexed signal being transmitted over a single twisted pair to the load. – T1 + –15V TTL DTL TO CMOS I/O EN CHANNEL SELECT AD7501 10k VOUT S1 S2 S8 +15V REMOTE TMP17s – T2 + – T8 + Figure 13. Remote Temperature Multiplexing To minimize the number of muxes required when a large number of TMP17s are being used, the circuit can be configured in a matrix. That is, a decoder can be used to switch the supply voltage to a column of TMP17s while a mux is used to control which row of sensors is being measured. The maximum number of TMP17s that can be used is the product of the number of channels of the decoder and mux. An example circuit controlling 80 TMP17s is shown in Figure 14. A 7-bit digital word is all that is required to select one of the sensors. The enable input of the multiplexer turns all the sensors off for minimum dissipation while idling. EN VOUT 10k +15V –15V ROW SELECT 4028 BCD TO DECIMAL DECODER COLUMN SELECT +15V 80–TMP17s Figure 14. Matrix Multiplexer To convert the TMP17 output to °C or °F, a single inexpensive reference and op amp can be used as shown in Figure 15. Although this circuit is similar to the two temperature trim circuit shown in Figure 5, there are two important differences. First, the gain resistor is fixed, alleviating the need for an elevated temperature trim. Acceptable accuracy can be achieved by choosing an inex- pensive resistor with the correct tolerance. Second, the TMP17 calibration error can be trimmed out at a known convenient temperature (e.g., room temperature) with a single potentiometer adjustment. This step is independent of the gain selection. – + – TMP17 OP196 RGAIN VOUT = 100mV/( C OR F) +5V V– ROFFSET/R GAIN RCAL R ROFFSET 2.5V REF43 ROFFSET 9.1k 9.8k RGAIN 100k 180k C F + Figure 15. Celsius or Fahrenheit Thermometer |
|
|
Link URL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Link do karty katalogowej | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |