| Zakładka z wyszukiwarką danych komponentów |
|
ADP5033ACBZ-1-R7 Arkusz danych(PDF) 5 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADP5033ACBZ-1-R7 Arkusz danych(HTML) 5 Page - Analog Devices |
|
5 / 28 page ![]() ADP5033 Rev. 0 | Page 5 of 28 Parameter Symbol Test Conditions/Comments Min Typ Max Unit POWER SUPPLY REJECTION RATIO PSRR Regulator LDO1 10 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 60 dB 100 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 62 dB 1 MHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 63 dB Regulator LDO2 10 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 54 dB 100 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 57 dB 1 MHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 64 dB 1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).2 2 This is the input current into VIN3/VIN4, which is not delivered to the output load. 3 Based on an endpoint calculation using 1 mA and 100 mA loads. 4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only to output voltages above 1.7 V. 5 Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, or 2.7 V. INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS TA = −40°C to +125°C, unless otherwise specified. Table 4. Parameter Symbol Min Typ Max Unit SUGGESTED INPUT AND OUTPUT CAPACITANCE BUCK1, BUCK2 Input Capacitor CMIN1, CMIN2 4.7 40 μF BUCK1, BUCK2 Output Capacitor CMIN1, CMIN2 10 40 μF LDO1, LDO21 Input and Output Capacitors CMIN3, CMIN4 0.70 μF CAPACITOR ESR RESR 0.001 1 Ω 1 The minimum input and output capacitance should be greater than 0.70 μF over the full range of operating conditions. The full range of operating conditions in the application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R- and X5R-type capacitors are recommended; Y5V and Z5U capacitors are not recommended for use with LDOs. |
|
Link URL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Link do karty katalogowej | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |