AM3703CUS datasheet(24/280 Pages) TI

24 / 280 page

AM3715, AM3703

SPRS616F

– JUNE 2010 – REVISED AUGUST 2011

www.ti.com

2.3

Ball Characteristics

Table 2-1 through Table 2-3 describe the terminal characteristics and the signals multiplexed on each pin

for the CBP, CBC, and CUS packages, respectively. The following list describes the table column

headers.

1. BALL BOTTOM: Ball number(s) on the bottom side associated with each signal(s) on the bottom.

2. PIN NAME: Names of signals multiplexed on each ball (also notice that the name of the pin is the

signal name in mode 0).

Note: Table 2-3 does not take into account subsystem pin multiplexing options. Subsystem pin

multiplexing options are described in Section 2.5, Signal Descriptions.

3. MODE: Multiplexing mode number.

(a) Mode 0 is the primary mode; this means that when mode 0 is set, the function mapped on the pin

corresponds to the name of the pin. There is always a function mapped on the primary mode.

Notice that primary mode is not necessarily the default mode.

Note: The default mode is the mode at the release of the reset; also see the RESET REL. MODE

column.

(b) Modes 1 to 7 are possible modes for alternate functions. On each pin, some modes are effectively

used for alternate functions, while some modes are not used and do not correspond to a functional

configuration.

4. TYPE: Signal direction

– I = Input

– O = Output

– I/O = Input/Output

– D = Open drain

– DS = Differential

– A = Analog

– PWR = Power

– GND = Ground

Note: In the safe_mode, the buffer is configured in high-impedance.

5. BALL RESET STATE: The state of the terminal at the power-on reset.

– 0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor.

– 1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor.

– Z: High-impedance

– L: High-impedance with an active pulldown resistor

– H : High-impedance with an active pullup resistor

6. BALL RESET REL. STATE: The state of the terminal at the release of the System Control Module

reset (PRCM CORE_RSTPWRON_RET reset signal).

– 0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor.

– 1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor.

– Z: High-impedance

– L: High-impedance with an active pulldown resistor

– H : High-impedance with an active pullup resistor

7. RESET REL. MODE: The mode is automatically configured at the release of the System Control

Module reset (PRCM CORE_RSTPWRON_RET reset signal).

8. POWER: The voltage supply that powers the terminal

’s I/O buffers.

9. HYS: Indicates if the input buffer is with hysteresis.

10. BUFFER STRENGTH: Drive strength of the associated output buffer.

TERMINAL DESCRIPTION

Submit Documentation Feedback

Product Folder Link(s): AM3715 AM3703

AM3703CUS Arkusz danych(PDF) 24 Page - Texas Instruments

AM3703CUS Arkusz danych(HTML) 24 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Arkusz danych Pobierz

Link URL