AM79C981 datasheet(10/40 Pages) AMD

10 / 40 page

AMD

PRELIMINARY

1–80

Am79C981

The reconnection algorithm option (standard or alter-

nate) is a global function for the TP ports, i.e. all TP ports

use the same reconnection algorithm. The AUI

reconnection algorithm option is programmed inde-

pendently of the TP port reconnection option.

Link Test

The integral TP ports implement the Link Test function

as specified in the 802.3 10BASE-T standard. The IMR+

device will transmit Link Test pulses to any TP port after

that port’s transmitter has been inactive for more than 8

to 17 ms. Conversely, if a TP port does not receive any

data packets or Link Test pulses for more than 65 to

132 ms and the Link Test function is enabled for that

port then that port will enter link fail state. A port in link

fail state will be disabled by the IMR+ chip (repeater

transmit and receive functions disabled) until it receives

either four consecutive Link Test pulses or a data pack-

et. The Link Test receive function itself can be disabled

via the IMR+ chip management port on a port-by-port

basis to allow the IMR+ device to interoperate with pre-

10BASE-T twisted pair networks that do not implement

the Link Test function. This interoperability is possible

because the IMR+ device will not allow the TP port to en-

ter link fail state, even if no Link Test pulses or data

packets are being received. Note however that the

IMR+ chip will always transmit Link Test pulses to all TP

ports regardless of whether or not the port is enabled,

partitioned, in link fail state, or has its Link Test receive

function disabled.

Polarity Reversal

The TP ports have the optional (programmable) ability

to invert (correct) the polarity of the received data if the

TP port senses that the received data packet waveform

polarity is reversed due to a wiring error. This receive

circuitry polarity correction allows subsequent packets

to be repeated with correct polarity. This function is exe-

cuted once following reset or link fail, and has a

programmable enable/disable option on a port-by-port

basis. This function is disabled upon reset and can be

enabled via the IMR+ chip Management Port.

Reset

The IMR+ device enters reset state when the

RST pin is

driven LOW. After the initial application of power, the

RST pin must be held LOW for a minimum of 150

µs

(3000 X1 clock cycles). If the

RST pin is subsequently

asserted while power is maintained to the IMR+ device,

a reset duration of only 4

µs is required. The IMR+ chip

continues to be in the reset state for 10 X1 clocks

(0.5

µs) following the rising edge of RST. During reset,

the output signals are placed in their inactive states.

This means that all analog signals are placed in their idle

states, bidirectional signals (except STR signal) are not

driven, active LOW signals are driven HIGH, and all ac-

tive HIGH signals and the STR pin are driven LOW.

An internal circuit ensures that a minimum reset pulse is

generated for all internal circuits. For a

RST input with a

slow rising edge, the input buffer threshold may be

crossed several times due to ripple on the input

waveform.

In a multiple IMR+ chip repeater the

RST signal should

be applied simultaneously to all IMR+ devices and

should be synchronized to the external X1 clock. Reset

synchronization is also required when accessing the

PAM (Port Activity Monitor).

The SI signal should be held HIGH for at least 500 ns fol-

lowing the rising edge of

RST.

Table 1 summarizes the state of the IMR+ chip following

reset.

Table 1. IMR+ Chip After Reset

Function

State After Reset

Pull Up/Pull Down

Active LOW outputs

HIGH

Active HIGH outputs

LOW

SO Output

HIGH

DAT, JAM

HI-IMPEDANCE

Either

STR

LOW

Pull Up*

Transmitters (TP and AUI)

IDLE

Receivers (TP and AUI)

ENABLED

Terminated

AUI Partitioning/Reconnection Algorithm

STANDARD ALGORITHM

N/A

TP Port Partitioning/Reconnection Algorithm

STANDARD ALGORITHM

N/A

Link Test Function for TP Ports

ENABLED, TP PORTS IN LINK FAIL

N/A

Automatic Receiver Polarity Reversal Function

DISABLED

N/A

*Only when used with the HIMIB device.

AM79C981 Arkusz danych(PDF) 10 Page - Advanced Micro Devices

AM79C981 Arkusz danych(HTML) 10 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Arkusz danych Pobierz

Link URL