RA4M2 datasheet(28/92 Pages) RENESAS

28 / 92 page

Under development Preliminary document

Specifications in this document are tentative and subject to change

RA4M3 Series

59. Electrical Characteristics

xx xx, 2019

RA4M2 Starget Spec

Page 10 of 2123

Figure 47.4 Temperature dependency in Deep Software Standby mode, power not supplied to SRAM or

USB resume detecting unit, power-on reset circuit low power function disabled (reference data)

Figure 47.5 Temperature dependency in Deep Software Standby mode, power not supplied to SRAM or

USB resume detecting unit, power-on reset circuit low power function enabled (reference data)

100

-40

-20

204060

100

Ta (℃)

Average value of the tested middle samples during product evaluation.

Average value of the tested upper-limit samples during product evaluation.

100

-40

-20

204060

100

Ta (℃)

Average value of the tested middle samples during product evaluation.

Average value of the tested upper-limit samples during product evaluation.

Figure 2.5

Temperature dependency in Deep Software Standby mode, power not supplied to SRAM or

USB resume detecting unit, power-on reset circuit low power function enabled (reference data)

2.2.6

VCC Rise and Fall Gradient and Ripple Frequency

Table 2.9

Rise and fall gradient characteristics

Parameter

Symbol

Min

Typ

Max

Unit

Test

conditions

VCC rising gradient

Voltage monitor 0 reset disabled at startup

SrVCC

0.0084 —

ms/V

—

Voltage monitor 0 reset enabled at startup

0.0084 —

—

SCI/USB boot mode*1

0.0084 —

—

VCC falling gradient*2

SfVCC

0.0084 —

—

ms/V

—

Note 1. At boot mode, the reset from voltage monitor 0 is disabled regardless of the value of the OFS1.LVDAS bit.

Note 2. This applies when VBATT is used.

Table 2.10

Rising and falling gradient and ripple frequency characteristics

The ripple voltage must meet the allowable ripple frequency fr(VCC) within the range between the VCC upper limit (3.6 V) and lower limit (2.7

V). When the VCC change exceeds VCC ±10%, the allowable voltage change rising and falling gradient dt/dVCC must be met.

Parameter

Symbol

Min

Typ

Max

Unit

Test conditions

Allowable ripple

frequency

fr (VCC)

—

kHz

Figure 2.6

Vr (VCC) ≤ VCC × 0.2

—

MHz

Figure 2.6

Vr (VCC) ≤ VCC × 0.08

—

MHz

Figure 2.6

Vr (VCC) ≤ VCC × 0.06

Allowable voltage

change rising and

falling gradient

dt/dVCC

1.0

—

ms/V

When VCC change

exceeds VCC ±10%

RA4M2 Datasheet

2. Electrical Characteristics

R01DS0367EJ0110 Rev.1.10

Jan 27, 2021

Page 28 of 92

RA4M2 Arkusz danych(PDF) 28 Page - Renesas Technology Corp

RA4M2 Arkusz danych(HTML) 28 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

Arkusz danych Pobierz

Link URL