7733 datasheet(98/940 Pages) RENESAS

98 / 940 page

7733 Group User's Manual

4–19

INTERRUPTS

____

4.10 External interrupts (INTi interrupt)

____

An external interrupt request occurs by input signal from pin INTi (i = 0 to 2). The occurrence condition of

an external interrupt request can be selected by the level sense/edge sense selection bit and the polarity

selection bit (bits 5 and 4 at addresses 7D16 to 7F16) shown in Figure 4.10.2. Table 4.10.1 lists the

____

occurrence condition of INTi interrupt request.

____

When using pins P62/INT0 to P64/INT2 as external interrupt input pins, set their corresponding bits at address

1016 (Port P6 direction register) to “0.” (Refer to “Figure 4.10.1.”) These pins can be pulled high by

____

software. (Refer to section “3.3 Pull-up function of P62 to P64 pins (INT0 to INT2).”

____

The INT2 interrupt is invalid when the key input interrupt selection bit (bit 7 at address 6D16) = “1.” (Refer

____

to chapter “5 KEY INPUT INTERRUPT FUNCTION.”) When using the INT2 interrupt function, clear the key

input interrupt selection bit to “0.”

____

A signal which is input to pin INTi requires a “H”/“L”-level duration of 250 ns or more independent of the

system clock frequency (Note 1).

____

Note that even when pins P62/INT0 to P64/INT2 are used as external interrupt input pins, these pins’ state

can be read in by reading bits 2 to 4 at address E16 (Port P6 register).

Note 1: When the falling edge or “L” level is selected as the interrupt occurrence condition, make sure that

“L”-level duration must be at least 250 ns: when the rising edge or “H” level is selected as the

interrupt occurrence condition, make sure that “H”-level duration must be at least 250 ns.

____

4.10 External interrupts (INTi interrupt)

____

Table 4.10.1 Occurrence condition of INTi interrupt request

b5 (Note 2)

b4 (Note 2)

____

Note 2: “b5” and “b4” represent bits 5 and 4 of the INT0 to INT2/key input interrupt control register. (Refer

to “Figure 4.10.2.”)

____

In an INTi interrupt, pin INTi’s state is always checked, and then an interrupt request is generated

____

according to the state. Therefore, when an INTi interrupt is not used, clear the INTi interrupt’s

priority level to “0.”

____

INTi

interrupt request occurrence condition

____

Occurs at the falling edge of an input signal to pin INTi (Edge sense).

____

Occurs at the rising edge of an input signal to pin INTi (Edge sense).

____

Occurs when pin INTi is at “H” level (Level sense).

____

Occurs when pin INTi is at “L” level (Level sense).

7733 Arkusz danych(PDF) 98 Page - Renesas Technology Corp

7733 Arkusz danych(HTML) 98 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Arkusz danych Pobierz

Link URL