MCP4441 datasheet(63/100 Pages) MICROCHIP

63 / 100 page

DS22265A-page 63

MCP444X/446X

7.2

Data Byte

Only the Read Command and the Write Command

have Data Byte(s).

The Write command concatenates the 8 bits of the

Data Byte with the one data bit (D8) contained in the

Command Byte to form 9 bits of data (D8:D0). The

Command Byte format supports up to 9 bits of data so

that the 8-bit resistor network can be set to Full-Scale

(100h or greater). This allows wiper connections to

Terminal A and to Terminal B. The D9 bit is currently

unused.

7.3

Error Condition

If the four address bits received (AD3:AD0) and the two

command

bits

received

(C1:C0)

are

valid

combination, the MCP44XX will Acknowledge the I2C

bus.

If the address bits and command bits are an invalid

combination, then the MCP44XX will Not Acknowledge

the I2C bus.

Once an error condition has occurred, any following

commands are ignored until the I2C bus is reset with a

Start Condition.

7.3.1

ABORTING A TRANSMISSION

A Restart or Stop condition in the expected data bit

position will abort the current command sequence and

data will not be written to the MCP44XX.

TABLE 7-3:

COMMANDS

Command Name

Writes

Value in

EEPROM

Operates on Volatile/

Nonvolatile memory

High

Voltage

(VIHH) on

HVC pin?

Impact on

WiperLock or

Write Protect

Works

when

Wiper is

“locked”?

Write Data

Yes (1)

Both

—

unlocked (1)

Read Data

—

Both

—

unlocked (1)

Increment Wiper

—

Volatile Only

—

unlocked (1)

Decrement Wiper

—

Volatile Only

—

unlocked (1)

High Voltage Write Data

Yes

Both

Yes

unchanged

High Voltage Read Data

—

Both

Yes

unchanged

Yes

High Voltage Increment Wiper

—

Volatile Only

Yes

unchanged

High Voltage Decrement Wiper

—

Volatile Only

Yes

unchanged

Modify Write Protect or WiperLock

Technology (High Voltage)

- Enable

— (2)

Nonvolatile Only (2)

Yes

locked/

protected (2)

Yes

Modify Write Protect or WiperLock

Technology (High Voltage)

- Disable

— (3)

Nonvolatile Only (3)

Yes

unlocked/

unprotected (3)

Yes

Note 1:

This command will only complete, if wiper is “unlocked” (WiperLock Technology is Disabled).

If the command is executed using address 02h, 03h 08h, or 09h; that corresponding wiper is locked or

if with address 0Fh, then Write Protect is enabled.

If the command is executed using with address 02h, 03h 08h, or 09h; that corresponding wiper is unlocked

or if with address 0Fh, then Write Protect is disabled.

MCP4441 Arkusz danych(PDF) 63 Page - Microchip Technology

MCP4441 Arkusz danych(HTML) 63 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Arkusz danych Pobierz

Link URL