LPC47M14X datasheet(81/205 Pages) SMSC

81 / 205 page

SMSC DS – LPC47M14X

Page 81

Rev. 03/19/2001

EPP DATA PORT 1

ADDRESS OFFSET = 05H

The EPP Data Port 1 is located at an offset of '05H' from the base address. Refer to EPP DATA PORT 0 for a

description of operation. This register is only available in EPP mode.

EPP DATA PORT 2

ADDRESS OFFSET = 06H

The EPP Data Port 2 is located at an offset of '06H' from the base address. Refer to EPP DATA PORT 0 for a

description of operation. This register is only available in EPP mode.

EPP DATA PORT 3

ADDRESS OFFSET = 07H

The EPP Data Port 3 is located at an offset of '07H' from the base address. Refer to EPP DATA PORT 0 for a

description of operation. This register is only available in EPP mode.

EPP 1.9 OPERATION

When the EPP mode is selected in the configuration register, the standard and bi-directional modes are also available. If

no EPP Read, Write or Address cycle is currently executing, then the PDx bus is in the standard or bi-directional mode,

and all output signals (STROBE, AUTOFD, INIT) are as set by the SPP Control Port and direction is controlled by PCD

of the Control port.

In EPP mode, the system timing is closely coupled to the EPP timing. For this reason, a watchdog timer is required to

prevent system lockup. The timer indicates if more than 10usec have elapsed from the start of the EPP cycle to nWAIT

being deasserted (after command). If a time-out occurs, the current EPP cycle is aborted and the time-out condition is

indicated in Status bit 0.

During an EPP cycle, if STROBE is active, it overrides the EPP write signal forcing the PDx bus to always be in a write

mode and the nWRITE signal to always be asserted.

Software Constraints

Before an EPP cycle is executed, the software must ensure that the control register bit PCD is a logic "0" (i.e., a 04H or

05H should be written to the Control port). If the user leaves PCD as a logic "1", and attempts to perform an EPP write,

the chip is unable to perform the write (because PCD is a logic "1") and will appear to perform an EPP read on the

parallel bus, no error is indicated.

EPP 1.9 Write

The timing for a write operation (address or data) is shown in timing diagram EPP Write Data or Address cycle. The

chip inserts wait states into the LPC I/O write cycle until it has been determined that the write cycle can complete. The

write cycle can complete under the following circumstances:

If the EPP bus is not ready (nWAIT is active low) when nDATASTB or nADDRSTB goes active then the

write can complete when nWAIT goes inactive high.

If the EPP bus is ready (nWAIT is inactive high) then the chip must wait for it to go active low before

changing the state of nDATASTB, nWRITE or nADDRSTB. The write can complete once nWAIT is

determined inactive.

Write Sequence of Operation

The host initiates an I/O write cycle to the selected EPP register.

If WAIT is not asserted, the chip must wait until WAIT is asserted.

The chip places address or data on PData bus, clears PDIR, and asserts nWRITE.

Chip asserts nDATASTB or nADDRSTRB indicating that PData bus contains valid information, and the WRITE

signal is valid.

Peripheral deasserts nWAIT, indicating that any setup requirements have been satisfied and the chip may

begin the termination phase of the cycle.

The chip deasserts nDATASTB or nADDRSTRB, this marks the beginning of the termination phase. If it

has not already done so, the peripheral should latch the information byte now.

The chip latches the data from the internal data bus for the PData bus and drives the sync that indicates

that no more wait states are required followed by the TAR to complete the write cycle.

Peripheral asserts nWAIT, indicating to the host that any hold time requirements have been satisfied and

acknowledging the termination of the cycle.

Chip may modify nWRITE and nPDATA in preparation for the next cycle.

LPC47M14X Arkusz danych(PDF) 81 Page - SMSC Corporation

LPC47M14X Arkusz danych(HTML) 81 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Arkusz danych Pobierz

Link URL