ATmega165 datasheet(53/336 Pages) ATMEL

53 / 336 page

ATmega165/V

2573G–AVR–07/09

External Interrupt Mask

• Bit 7 – PCIE1: Pin Change Interrupt Enable 1

When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),

pin change interrupt 1 is enabled. Any change on any enabled PCINT15..8 pin will

cause an interrupt. The corresponding interrupt of Pin Change Interrupt Request is exe-

cuted from the PCI1 Interrupt Vector. PCINT15..8 pins are enabled individually by the

PCMSK1 Register.

• Bit 6 – PCIE0: Pin Change Interrupt Enable 0

When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),

pin change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause

an interrupt. The corresponding interrupt of Pin Change Interrupt Request is executed

from the PCI0 Interrupt Vector. PCINT7..0 pins are enabled individually by the PCMSK0

• Bit 0 – INT0: External Interrupt Request 0 Enable

When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),

the external pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and

ISC00) in the External Interrupt Control Register A (EICRA) define whether the external

interrupt is activated on rising and/or falling edge of the INT0 pin or level sensed. Activity

on the pin will cause an interrupt request even if INT0 is configured as an output. The

corresponding interrupt of External Interrupt Request 0 is executed from the INT0 Inter-

rupt Vector.

External Interrupt Flag

• Bit 7 – PCIF1: Pin Change Interrupt Flag 1

When a logic change on any PCINT15..8 pin triggers an interrupt request, PCIF1

becomes set (one). If the I-bit in SREG and the PCIE1 bit in EIMSK are set (one), the

MCU will jump to the corresponding Interrupt Vector. The flag is cleared when the inter-

rupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to

it.

• Bit 6 – PCIF0: Pin Change Interrupt Flag 0

When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0

becomes set (one). If the I-bit in SREG and the PCIE0 bit in EIMSK are set (one), the

MCU will jump to the corresponding Interrupt Vector. The flag is cleared when the inter-

rupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to

it.

Bit

654

PCIE1

PCIE0

–

–INT0

EIMSK

Read/Write

R/W

Initial Value

Bit

654

PCIF1

PCIF0

–

INTF0

EIFR

Read/Write

R/W

Initial Value

ATmega165 Arkusz danych(PDF) 53 Page - ATMEL Corporation

ATmega165 Arkusz danych(HTML) 53 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Arkusz danych Pobierz

Link URL